, ,

Hobart PW10eR Utensil Washer –

Brand:

Racks per hour – 2 Minute 4 Minute 6 Minute
Wash Wash Wash
PW10 20 12 8
PW10eR 13 9 7
1.2 gallons of water per cycle
Timed wash cycles for 2-4-6 minutes
Hot water sanitation machines
Steam Elimination and Energy Recovery
(Advansys only)
Sense-A-Temp™ booster heater capable of 70° rise
Front loading, split-door configuration
Chamber accepts 10 full-sized sheet pans, or
140 quart mixing bowl
Advanced Service diagnostics
Advanced Delime notification and cycle (includes
booster) (Advansys only)
16 gauge stainless steel deep drawn tank
Microcomputer controls with advanced digital
cycle/temperature display
Two revolving upper and lower anti-clogging
wash arms and rinse arms
Removable stainless steel scrap screens and
scrap basket
Corrosion resistant pump
Automatic pumped drain
Pumped rinse
33.79″ door opening
Automatic fill
Delime pump standard (Advansys)
Electric tank heat
Spray hose

Spec Sheet Warranty

For more information about lease and rent options please call us at (604) 569-3400.

Call for Pricing:(604) 569-3400
Compare

DESIGN: Heavy duty, fully automatic, front opening Prep Washer
with split-door system. Upper door section slides upward as the
lower door section is pulled down. Stainless steel pull-out rack
allows easy loading for large utensils and pans. Three variable
wash cycles ensure thorough cleaning and sanitizing
CONSTRUCTION: Stainless steel tank and chamber, door, frame,
legs and adjustable feet.
PUMP: Pump capacity 211 gpm.
MOTOR: 208-240/60/3 or 480/60/3 configurations. Factory sealed
lubrication, TEFC with sealed ball bearings. Thermal overload
protection.
WASH AND RINSE CYCLE: Complete automatic type, controlled
by microprocessor electronics. Cycle may be interrupted any time
by opening door. Cycle continues when door is closed.
Initial cycle fills wash tank, to be recirculated each wash cycle.
Some wash water is drained off before rinse cycle. Rinse cycle
refreshes wash water and tank heat.
RINSE PUMP: Powered by a 1⁄3 H.P. 3Ø TEFC motor, the rinse
pump is made of high strength engineered composite material.
BLOWER: The condenser blower is an all stainless steel forward
curved centrifugal wheel powered by a 1⁄16 H.P. TEFC single phase
motor for nearly silent operation.
CONDENSER COIL: The condensing system using a tube and fin
coil constructed of copper and corrosion resistant aluminum.
ELECTRIC BOOSTER HEATER: Electric booster with Sense-ATemp™ technology adequately sized to raise 110° inlet water to
180°.
Racks per hour – 2 Minute 4 Minute 6 Minute
Wash Wash Wash
PW10 20 12 8
PW10eR 13 9 7
1.2 gallons of water per cycle
Tank Capacity – Gallons 21 gallons
Overall Dimensions – H x W x D 78.04″ H x 34.86″ W x 37.20″ D 88.47″ H x 34.86″ W x 37.20″ D
Wash Cycle Time – Minutes 2, 4, 6 minutes
Water Usage Per Cycle – Gallons 1.2 gallons
Drain Design Pumped
Door Opening Height x Width 33.79″ H x 26.185″ W
Chemical Connection Capability Standard
Delime Pump N/A Standard
Peak Drain Flow – GPM 18
Advanced Service Diagnostics Standard Standard
Advanced Cleaning Cycle N/A Standard
70° Rise Sense-A-Temp™ Booster Heater Standard
Incoming Water Temperature Required (minimum) 110° 55°
SPECIFICATIONS
CYCLE OPERATION:
PW10eR: The microcomputer-timing program is started by closing
the doors and actuating the wash cycle button. The microcomputer energizes the wash pump motor contactor during the wash
portion of the program. After the wash, a dwell permits the upper
wash manifold to drain. At the end of the dwell, the final rinse
pump is energized. After the final rinse pump turns off, the Blower
and Cold Water Valve turn on for 120 seconds to condense the
vapor laden air inside the chamber. After 120-140 seconds is
complete the Cycle Light turns OFF, completing the program.
RINSE AND SANITATION:
PW10/10eR: Sanitation is accomplished by means of a builtin booster heater designed to raise temperature of water to a
minimum of 180°F from an incoming water temperature of 110°F
for PW10 and 55°F for PW10eR.
ENERGY RECOVERY: Heat energy is recovered from the condensation of vapors in the chamber at the end of each cycle. This
pre-heats the water for the next rinse cycle from 55°F up to 140°F.
PUMPED DRAIN: Machine automatically drains water
through a built-in pump. Maximum 38″ drain height permitted.
RACKING: Standard rack assortment consists of one flatbottomed frame rack, one flat grid insert rack and one tray support
insert rack.
SPECIFICATIONS: Listed by Underwriters Laboratories Inc. and
NSF International.

Based on 0 reviews

0.0 overall
0
0
0
0
0

Be the first to review “Hobart PW10eR Utensil Washer –”

There are no reviews yet.